Chrysler 300M Enthusiasts Club
  • Group Buy Intake Manifold spacers $40.00 + actual shipping. DEADLINE 11/11/19 For Ordering CLOSED

  • Club Members Only may Post an ad to buy or sell something
Membership Banner

Club Members Only may Post an ad to buy or sell something

Moderator: Moderators

 #382043  by dcsally97
 January 23rd, 2020, 6:42 pm
beespecial wrote: January 23rd, 2020, 4:44 pm Upon further review, I've decided on the hex head zinc plated 100mm bolts from Bolt Depot. I got a couple of extras to see if I can cut the bolt down closer to 95mm so I don't have to use multiple washers .
Smart man
User avatar
 #382081  by Sneke_Eyez
 January 27th, 2020, 4:11 pm
I was doing some cleaning and organizing yesterday and found my 7 bolts and lock washers left over from the extra V3 intake spacer I bought from Steph.

I had honestly forgotten they were stainless, but I will be using them with this new spacer. Rather than lock washers I intend to go with 2 stainless flat washers.
User avatar
 #382341  by M-Pressive
 February 18th, 2020, 2:33 pm
Sojiaraggs9000 wrote: February 18th, 2020, 2:17 pm Any of you guys installed these yet?
A bunch of us have them.

viewtopic.php?f=49&t=36642
User avatar
 #382343  by beespecial
 February 18th, 2020, 3:32 pm
Sojiaraggs9000 wrote: February 18th, 2020, 2:17 pm Any of you guys installed these yet?
I have mine installed. It doesn't provide eyeball flattening quickness but it's enough to know that it's better than stock.
 #382344  by Sojiaraggs9000
 February 18th, 2020, 6:19 pm
Heck yeah. I'm actually going to try this in my homemade 4.0L stroker. Its a combination of a 3.5L inertia big valve performance heads, V1.2 blower cams, ported lower intake manifold all attached to a 2008 4.0L Dodge Nitro engine. Should see 420-450 rwhp.
User avatar
 #382345  by LUNAT1C
 February 18th, 2020, 6:22 pm
Sojiaraggs9000 wrote: February 18th, 2020, 6:19 pm Heck yeah. I'm actually going to try this in my homemade 4.0L stroker. Its a combination of a 3.5L inertia big valve performance heads, V1.2 blower cams, ported lower intake manifold all attached to a 2008 4.0L Dodge Nitro engine. Should see 420-450 rwhp.
Make sure you triple check that it will fit that engine. These spacers are designed to be used between the 2nd-gen LH 3.2/3.5L intake plenum and lower intake manifold. I've no idea if that will fit the LX 3.5L or Nitro 4.0L.
 #382346  by Sojiaraggs9000
 February 18th, 2020, 6:28 pm
They're the same as far as i can tell. FYI 4.0L block is the same, heads are the same and will bolt up. Here is my ported LIM.
You do not have the required permissions to view the files attached to this post.
LUNAT1C, beespecial liked this
User avatar
 #382353  by FIREM
 February 19th, 2020, 12:38 pm
UPDATE: students ran into some issues completing the last few spacers. Back on track and hope to complete this week. Now that I have retired, spacers will ship to me in SC, than once received they will be sent out. Sorry for the delays but the end is in sight.
User avatar
 #382453  by FIREM
 February 24th, 2020, 9:24 pm
I am still waiting to receive the remainder of the order. There MAY be one extra. Will let you know IF that is the case.
  • 1
  • 3
  • 4
  • 5
  • 6
  • 7